Digital Housing
i n s t r u c t i o n m a n u a l
f o r
Sony
DSC-H5
H o u s i n g
#6111.5
Diffuser/Deflector
material
DDiiffffuusseerr aanndd DDeefflleeccttoorr IInnssttaallllaattiioonn
A diffuser and deflector are
included with the housing. The
diffuser is white transparent
CChheecckkiinngg CCoonnttrroollss
Once the housing has been closed, push the controls back into
place. Make sure they line up with the camera’s controls.
plastic. The deflector is also
TTuurrnn CCaammeerraa OOnn
This edge
white but is not transparent
against
Turn the camera on and operate each of the housing controls to
get a feel for using the camera in the housing. Take a few
pictures above water with the camera in the housing.
and has a decal on the front.
housing
Port Clamp
To install the diffuser or deflector
spread the port clamp at the spring
end and slide over the lens port. The
white plastic should be placed in front
of the camera flash. The port clamp
should be pushed back against the
front of the housing.
Spring
JJoogg DDiiaall CCoonnttrrooll
White Dot
The Jog Dial on the camera must be pressed
Spread to Install
in to select a value or item. Once a
selection is made the Jog Dial is then
rotated to change the setting values when
shooting with the manual adjustment
modes. Viewing next/previous images is
also done by rotating the Jog Dial.
Diffuser
DDiiffffuusseerr
The diffuser should be installed
when using the camera's built
in flash. When shooting with
the camera's built-in flash at
approximately 2 feet (0.6 m)
or less, the lens port on the
housing may block a portion
of the light from the camera's
built-in flash, creating a shadow
Bump
The housings Jog Dial Control has a bump on
Jog Dial Control - Top View
the inside face of the control for
depressing the Jog Dial. When the white dot on the control
knob is in the 12 o’clock position the bump is aligned with the
Jog Dial. In this position you can push in and pull out on the
housing Jog Dial control to select a value or item. Once selected
the housing Jog Dial control can then be rotated to change the
setting values.
Housing shown with
Diffuser installed.
in the lower left of the photo. If this occurs, zoom the lens slightly
to eliminate the shadow. (You can test this above water)
The Jog Dial on the camera is small. It will take some practice to
become proficient at operating the Jog Dial with the camera
housing control.
DDeefflleeccttoorr
The deflector should be installed when using an external strobe
such as the DS51 or DS125 Substrobe and EV Controller. The
deflector will redirect the camera's flash to the EV Controller
which controls the external strobes output.
5
6
QQuuiicckk--RReelleeaassee BBaassee,, HHaannddlleess aanndd TTrraayy
Quickk-Rellease Base
Quick Release Base
The Quick-Release Base is
Slot
plastic. A toggle lever located
underneath the base allows
the base to be easily removed
from the Tray. Turn the
housing upside down, pull
out on the toggle lever.
Rotate the lever 90° to
remove the base.
Handless and Tray
Flip Quick Release
Lever Up
The housing handles are
rubber and the tray is
aluminum. Their weight
helps to offset the buoyancy
of the housing. The complete
assembly is slightly negative
underwater for better
control. The handles have a
push button release for easily
Rotate Quick
Release Lever
attaching and removing
strobe arms. The tray and
handles can be removed from
the housing. To remove the
tray, the base must be
removed to gain access to
the nuts holding the tray on
the housing. Remove the 2
nuts, washers and rubber
spacers. DO NOT remove
the bolts protruding through
Remove Quick
Release Lever
the housing.
and Base
7
LLeennss PPoorrtt
OOppttiioonnaall AAcccceessssoorriieess CCoonnttiinnuueedd
Substrobe
DS125
The Lens Port is factory sealed, do not remove.
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the lens port to avoid water spotting. To clean
use a mild soap solution or lens cleaner.
Substrobe
DS51
Do not use alcohol or window cleaner on the Lens Port.
UUssiinngg WWiiddee--AAnnggllee LLeennsseess
The Lens Port is threaded so that accessory lenses can be
screwed onto the port. The threads are very fine, take care not
to cross thread the lens.
Wide angle lenses are available from Inon, Sea & Sea and
Epoque. These lenses can be screwed onto the lens port above
or below water. These lenses are designed to have water
between the front of the port and the accessory lens. Make sure
no air bubbles are trapped between the port and the accessory
lens. There may be slight vignetting when these wide angle
lenses are installed. Any
SA-100Q
Arm
SA-100Q
Arm
Wide Angle Lens
vignetting that occurs can
be eliminated by zooming
the camera lens slightly.
To properly light subjects
when using a wide angle
accessory lens an external
strobe should be used.
Due to the wide angle of
coverage of the Inon, Sea
& Sea and Epoque lenses,
the DS125 Substrobe is
recommended or two
EV Controller
EV Controller
SSuubbssttrroobbee DDSS5511
SSuubbssttrroobbee DDSS112255
The Substrobe DS51 covers the
equivalent of a 28mm lens. It is
the ideal choice when using
only the camera lens or the
camera lens with a macro
accessory lens.
The Substrobe DS125 covers
the equivalent of a 18mm
lens, 100 degrees. It is the
ideal choice when using
accessory wide angle lenses
greater than 28mm.
Housing shown with
DS51 Substrobes.
accessory wide angle lens.
8
9
OOppttiioonnaall AAcccceessssoorriieess
MMaaiinntteennaannccee
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
BBaacckk OO''rriinngg #0132.59
O'rings last for several years if properly maintained. (See
maintenance) Always carry a spare.
Do Not
1.
leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
UURR//PPrroo FFiilltteerr #6441.41
The UR/Pro underwater color correcting filter is designed to
restore some of the warm colors filtered out by the water. For
available light use only, not recommended for use with flash.
2. Do Nott ship the camera in the housing.
3. Before using the housing, always check the tightness of the
screw in each control knob.
set
controol gland
Check each
penetrating the housing to make sure
U
U
s
s
i
i
n
n
g
g
a
a
D
D
S
S
S
S
u
u
b
b
s
s
t
t
r
r
o
o
b
b
e
e
&
&
EV-Controller
EV-Controller
they are tight. There is a slight chance that either could vibrate
loose during travel.
To use a external DS Substrobe requires the EV-Controller. The EV-
Controller has a built-in slave sensor that is triggered by the camera’s
built-in flash which fires the external DS Substrobe. The EV-
Controller provides 10 manual power settings in 1/2 stop increments
for precision lighting.
4. Keep the back o’ring clean and lightly lubricated. To lubricate
remove the o’ring from the back. Put a small amount of lkelite
lubricant on your fingers. Draw the o’ring through your fingers
to apply a light coating of lubricant. Only apply enough
Do Not sstretcch the oo’ring
lubricant to make the o’ring feel slick.
.
S
S
u
u
b
b
s
s
t
t
r
r
o
o
b
b
e
e
P
P
a
a
c
c
k
k
a
a
g
g
e
e
s
s
a
a
v
v
a
a
i
i
l
l
a
a
b
b
l
l
e
e
This light coating of lubricant will help to keep the o’ring from
drying out and will help to show a dark sealing line when the
housing back is properly sealed.
Ikelite Ball Arm Systems are provided with these packages
#3944.47 SubStrobe DS51 with EV Controller
#3944.54 SubStrobe DS51 with EV Controller
#3944.77 SubStrobe DS125 with EV Controller
5. Keep the area where the o’ring fits and the sealing surface of
the housing clean.
6. Rinse the housing exterior thoroughly in fresh water after each salt
water use. Dry with a soft cloth. Dry lens port to eliminate water
spotting.
After several uses in salt water soak the housing in a mild soap
solution, rinse and dry before storage. When storing the housing,
remove the back o’ring, lightly lubricate and place in a plastic bag.
Place the plastic bag with o’ring inside the housing for safe keeping.
CCAAUUTTIIOONN
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
10
11
3. Some of the controls have a short shaft and cannot be pulled
out exposing the shaft for lubrication. In the unlikely event one
of these controls sticks or becomes difficult to operate you can
remove the control from the housing and lubricate it, or return
the housing to Ikelite for maintenance. To remove the control,
loosen the set screw in the knob (allen wrench required);
remove the knob. If there is salt or dirt build-up on the exposed
control shaft, clean the shaft. Open the housing and gently slide
the control shaft out of the control gland. Clean and lightly
lubricate the shaft, including the end of the shaft. Slide the
shaft back into the control gland and gently slide it back and
forth a few times without fully removing the shaft from the
gland. Replace the knob, NOTE the flat area on the shaft, the
set screw in the knob should tighten down against the flat area
on the control so the knob does not turn on the shaft.
CCoonnttrrooll MMaaiinntteennaannccee
Ikelite controls are designed to provide years of reliable service
with minimal maintenance.
1. Push button controls require no maintenance other than rinsing
in fresh water after saltwater use. If a push button control
becomes difficult to push or if it sticks when depressed, soak the
housing in luke warm fresh water. After a few minutes operate
the push button. If this does not correct the problem, return the
housing to Ikelite for maintenance.
2. Some of the controls have long shafts. These controls can be
lubricate shaft
housing
pull out to
expose shaft
housing
gland
control
shaft
pulled out, exposing the shaft (see drawing).
To lubricate the control, gently pull on the knob until the
stainless steel shaft is exposed. Lightly lubricate the shaft, then
move the shaft in and out several times. This will lubricate the
x’ring in the Ikelite control gland. This should be done before
using the housing after a prolonged storage period, or once a
week when the housing is in use.
Loosen set screw
(allen wrench required)
Flat
Tighten set screw down
against this area when
replacing the knob.
Lubricate end of shaft
before reinserting into
gland
12
13
GGeenneerraall TTiippss
PPhhoottoo TTiippss
1. Due to the power required to operate the camera, flash, and
LCD screen it is a good idea to start each dive with a fresh set of
batteries.
1. The number one rule in underwater photography is eliminate as
much water between camera and subject as possible. Get as
close as you can to the subject, then use the zoom. If you are
using flash, subjects beyond 6 feet (1.8m)will not have much
color.
2. Some cameras reset their flash to AUTO when the camera is
turned on. If you prefer another setting be sure to select it.
3. As soon as you enter the water, take a moment and check the
housing to see that it is properly sealed.
4. Next, check to see if there are any bubbles on the face of the
lens port. If there are, take your finger and remove them. If
there are bubbles on the lens port they can produce soft focus
spots in your photographs.
2. The camera’s built-in flash is very close to the camera lens. The
flash will light up any suspended particles in the water and they
will be recorded in your picture. This effect is called backscatter.
To eliminate as much backscatter as possible, photograph close.
Photograph in clear water; do not stir up the sand or silty
bottom. If backscatter becomes a problem in the environment
you are photographing, an external flash will help eliminate
much of the backscatter.
3. Digital cameras have a slight lag time between when you press
the shutter release button and the camera actually takes the
picture. Hold the camera steady a second or two after pressing
the shutter release button.
4. Do not shoot down on subjects as they will quite often blend
into the background and be difficult to see in the photograph.
Shoot subjects straight on or shoot up at a slight angle using
the blue water as a contrasting background.
5. Underwater flash is used to restore the warmer colors filtered
out by the water as well as to illuminate the subject. When
photographing underwater, set the camera to use flash on
every shot. If the camera’s flash is set to AUTO and the sun is
behind your subject, the camera may see enough light that it
does not fire the flash. With the sun behind the subject the
subject is shaded (dark) and needs flash for a good exposure.
LLuubbrriiccaannttss
1. Ikelite provides silicone lubricant with the housing. We
recommend that you use only Ikelite lubricant on Ikelite
products as some other brands may cause the o’ring to swell
and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and
o’rings. Wipe off any excess lubricant with a clean cloth.
Lubricant is not a sealant, it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing.
CAUTION
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
14
15
IIkkeelliittee LLiimmiitteedd WWaarrrraannttyy
All Ikelite products are warranted against any manufacturing
defects for a period of one (1) year from the date of purchase.
Defective products should be returned prepaid to Ikelite. Ikelite
will, at its discretion, repair or replace such products, and will
return to customer prepaid. All other claims, of any nature,
including but not limited to bulb failure are not covered. Except as
mentioned above, no other warranty expressed or implied, applies
to this Ikelite product.
RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviiccee
Ikelite is most interested in preforming any service to assure that
all products perform as intended. For repair or service, return the
product to the address below with your name, address, phone
number and a brief description of the problem. Evidence of
purchase date must be provided to obtain warranty service.
Ikelitte Underrwater SSystems
50 W 33rdd Street
Indiannapoliiss, IN 462208 USA
317-9223-4523
email: iikelitee@ikeliite.com
Digitaal 61111.5-011-0806
|